Е а висока мощност електрически поялник добро или а ниска мощност един% 3f
Електрическото желязо не не съществува% 2c мощността е високо или силата е малко!
There are many kinds of power for electric irons, the smaller ones are 15 watts, 20 watts, the larger ones are 200 watts, 300 watts, and the pistol-style 500 watts. When performing welding work, the power of the soldering iron must be determin according to the welding object, and sometimes the power of the electric contact iron must be selected according to the climate season (winter, summer). За запояване електронни компоненти% 2c 15 вата до 20 вата е добре. Ако вие използвате 500 вата % 2c веднъж на запояване желязо отива надолу % 2c това ще бъде а черна дупка. На разбира се% 2c то е не добро.
Дали мощността селекцията е подходяща или не зависима главно на топене и поток на спойка. Това процес прави не надвишава три секунди. Ако то е твърде дълго, it ще повреди електронните компоненти, ако то е също кратко, заваряването ще не бъде надеждни, и на спойка ставите ще не бъде гладка.
Обикновено, запояване ютии с малки крака такива като резистори, кондензатори, транзистори, и интегрирани блокове трябва да се използва с a 20-watt запояване желязо. То е подходящо запояване 35 вата до 40 вата когато заваряване топлина мивки, трансформатори, екраниране капаци и други едрокрак устройства, или заземяване голяма площ облицовани с мед плочи. Следователно, според до заваряване обект, на мощност на запояване желязо трябва бъде правилно избрано. Там е не такова нещо като висока мощност или ниска мощност.
Въведение към принципа на електрически запояване желязо
Use the ohm range of the multimeter to measure whether there is an open circuit or short circuit at both ends of the plug, and then use the Rx1000 or Rx10000 range to measure the resistance between the plug and the shell. If the pointer does not move or the resistance is greater than 2-3MΩ, it can be used safely without leakage. The soldering iron core of the internal heating type electric soldering iron is made of a relatively thin nickel-chromium resistance wire wound on a porcelain tube. Its resistance is about 2.5kΩ (20W), and the temperature of the soldering iron can generally reach about 350OC. Because the internal heating type electric soldering iron has the characteristics of fast heating, light weight, low power consumption, small size and high thermal efficiency, it has been widely used. After the soldering iron is connected to the power supply, if it is not hot or not too hot, check whether the power supply voltage is lower than AC210V (the normal voltage should be AC220V). If the voltage is too low, it may cause insufficient heat and difficulty in soldering. The soldering iron tip is oxidized or the fastening part between the root end of the soldering iron tip and the inner wall of the outer tube is oxidized. The reason for the electrification of the neutral line is that in the three-phase four-wire power supply system, the neutral line is grounded and has the same potential as the earth. If the neon bulb glows when tested with a test pen, it indicates that the zero line is charged (there is a potential difference between the zero line and the earth). The open circuit of the neutral line, the increase of the grounding resistance of the neutral line or the open circuit of the grounding downconductor and the grounding of the phase line will all cause the neutral line to be charged.
